Search found 690 matches

by John_S
Sat Jul 07, 2018 10:44 pm
Forum: Live Steam
Topic: How do you guys feel about the "Just get it done" attitude?
Replies: 20
Views: 1082

Re: How do you guys feel about the "Just get it done" attitude?

Remember that there are times to build a watch and times to build a locomotive and get it out on the track. My similar approach was, "I'm not sending this to the international space station" when it came to precision on some parts. Yes, there are certain very critical dimensions and tolerances on s...
by John_S
Sat Jul 07, 2018 10:37 pm
Forum: Live Steam
Topic: Piston mounting
Replies: 5
Views: 408

Re: Piston mounting

On my mogul, the SS rod is threaded into the bronze piston and then silver soldered. You should never have to disassemble the rod from the piston after assembly.
by John_S
Fri Jun 15, 2018 9:36 pm
Forum: Build Log
Topic: Restoring a modified Allen 2-4-0 barn find
Replies: 122
Views: 32082

Re: Restoring a modified Allen 2-4-0 barn find

Pieces of .010 stainless shim did the trick. Then it was on to the valve gear. I had a massive amount of valve rod slop when running the locomotive last year, so I knew I'd need to replace a lot of stuff. I started by ordering the Allen EDM cut expansion links and die blocks. New link pins for the ...
by John_S
Sat Jun 09, 2018 7:36 pm
Forum: Live Steam
Topic: RANT THREAD?
Replies: 95
Views: 6212

Re: RANT THREAD?

cbrew, I built the rack for the exact same reason: So I can pull the camper and have the loco, tender, and boxcar. My boxcar houses the air compressor and resevoire for my train brakes as well as the 12v battery for lights, plus tools and parts that I may need if things go Tango Uniform out on the t...
by John_S
Fri Jun 08, 2018 12:15 pm
Forum: Live Steam
Topic: RANT THREAD?
Replies: 95
Views: 6212

Re: RANT THREAD?

6) figure out a way to quickly load or unload your equipment when visiting other tracks. This is a sure way to kill an experience when you're stuck behind someone taking his time to get on/off a railroad. If nothing else, load the equipment, secure it so you can move out of the way to finish tying ...
by John_S
Sun May 27, 2018 6:34 pm
Forum: Live Steam
Topic: Stainless steel boiler/exchanger?
Replies: 84
Views: 6845

Re: Stainless steel boiler/exchanger?

My two cents: Save your money, build your boiler from a good piece of pipe and 516-70 carbon. It will outlast any savings you'd gain by spending 5x as much on stainless.
by John_S
Wed May 16, 2018 1:47 pm
Forum: Live Steam
Topic: Mid-South LS Spring Meet
Replies: 22
Views: 1814

Re: Mid-South LS Spring Meet

So glad to see the roof over the steaming bays! Wish I could have made it up there for the meet; perhaps in the fall this go-round.
by John_S
Sun May 13, 2018 6:53 pm
Forum: Live Steam
Topic: RANT THREAD?
Replies: 95
Views: 6212

Re: RANT THREAD?

On snagging hoses: If you are working with any kind of hose, line, or rope, it will snag when you pull it such that you'll have to climb down off the roof to unsnag it. But if you want to loop it around something, you won't be able to do it, and you'll have to climb down off the roof to loop it. Di...
by John_S
Sun May 13, 2018 6:49 pm
Forum: Live Steam
Topic: Steel Prices
Replies: 12
Views: 2415

Re: Steel Prices

Aluminum has had the most significant increase in cost over the last two months. Carbon bar products (HR bar, 1018, 1045, etc.) have been minimal but rising. Carbon sheet and plate is up over 10cent/lb since February and supply is becoming limited. If you're looking for 516-70 for boilers, you'd bet...
by John_S
Sun Apr 22, 2018 2:23 pm
Forum: Live Steam
Topic: Allen Mogul Timing
Replies: 9
Views: 1179

Re: Allen Mogul Timing

Are your outside rocker arms silver soldered onto the shaft, or still only held in by the roll pins (as called for on the drawings)? This was a design flaw that is known and almost everyone goes back and silver solders the arms to the shaft. The pins would wear the bronze arm casting and introduce a...
by John_S
Sat Apr 07, 2018 5:03 pm
Forum: Live Steam
Topic: Passing of Doug Van Veelen
Replies: 5
Views: 1330

Re: Passing of Doug Van Veelen

This is sad news. Doug was a member of the original North Georgia Live Steamers (1980s-1990s) in Duluth, GA, and was an authority on the Gainesville Midland railroad.
by John_S
Fri Mar 16, 2018 7:06 pm
Forum: Live Steam
Topic: Steel Prices
Replies: 12
Views: 2415

Re: Steel Prices

FYI, I work for Ryerson and I am intimately familiar with what's happening. Yes, there are increases happening and it's a day-to-day thing at the moment. Steel is far less affected than aluminum and the increases are much less, comparably. We're swamped at the moment due to a somewhat artificial dem...