Search found 80 matches
- Fri Jul 14, 2006 2:08 pm
- Forum: Site Software Questions and Answers
- Topic: Lost pic's.
- Replies: 5
- Views: 7670
- Thu Jul 13, 2006 8:02 pm
- Forum: Site Software Questions and Answers
- Topic: Lost pic's.
- Replies: 5
- Views: 7670
Lost pic's.
5/23/03 I posted a pic. of my Rhodes Shaper in the photo section. It has disappeared along with all other pic's. I have posted. The shaper pic. was the only one I had left of it when it was sporting new paint and bright metalwork. Is there anyway to retrieve the lost pic.?
- Wed Jul 07, 2004 7:34 pm
- Forum: General Discussion
- Topic: What parts for air compressor rebuild?
- Replies: 18
- Views: 6239
Re: What parts for air compressor rebuild?
If it were me, first thing I would do is fix all the air leaks so it would'nt be starting from 0. Then if you don't realy need 175psi lower the cut out to 150psi. Too small wire size can also extend the run time. I would also change the oil to make sure it has the mfg. recomended oil. My compressor ...
- Wed Jul 07, 2004 6:12 pm
- Forum: The Junk Drawer
- Topic: Cheepo Knock-Off Digital Protractor Question
- Replies: 2
- Views: 2511
Re: Cheepo Knock-Off Digital Protractor Question
A friend has a cheap-o he uses building race cars and street rods. I checked it against a Starrett and it was off 3 degrees. After recalibrating, it seems to be OK. There may be a few unhappy pinion angles out there.
- Fri Jun 11, 2004 10:28 pm
- Forum: General Discussion
- Topic: Wahlstrom Chuck - value?
- Replies: 12
- Views: 5358
Re: Wahlstrom Chuck - value?
The reason they're in such good condition is nobody likes to use them, they have'nt been used. You have to think to use them, who wants to do that? For drilling several different size holes I always use an Albrecht, for drilling and taping I use a Jacobs 34. The Jacobs N chucks are A-OK but the larg...
- Thu Jun 10, 2004 7:30 pm
- Forum: Site Software Questions and Answers
- Topic: Registered date
- Replies: 0
- Views: 3159
Registered date
The registered date under my name has Jan 05, is that when I'm expected to show up?
- Wed Jun 09, 2004 8:07 pm
- Forum: Milling Machines
- Topic: Mill upgrade advice please
- Replies: 9
- Views: 4511
- Thu Dec 18, 2003 10:14 pm
- Forum: General Discussion
- Topic: OFF TOPIC - Need Help - anyone with a F150 six
- Replies: 20
- Views: 5799
Re: Belt squeal
Jacin, as someone else said the power steering pulley is supposed to be flush with the pump shaft. Sometimes even then it needs to be moved in or out to get proper alignment. Looking at your pic. the pulley looks to be pressed on about 1/8" too far. Another thing to check is the crankshaft end ...
- Tue Dec 16, 2003 8:39 pm
- Forum: General Discussion
- Topic: Positioning Table w/scales
- Replies: 4
- Views: 2766
Re: Positioning Table w/scales
Jon, I sent you an email, did you get it?
- Sun Dec 14, 2003 6:34 pm
- Forum: General Discussion
- Topic: Positioning Table w/scales
- Replies: 4
- Views: 2766
Positioning Table w/scales
I recently acquired a positioning table made by Daedal Inc. It has about 6-1/4"x6-1/4" travel X&Y. It has 2 scales (glass?) made by Dynamics Research Corp. What type of DRO would be needed for these scales? Anyone care to put a price on this gadget? I think I'll sell it.
- Sat Jun 21, 2003 10:57 pm
- Forum: General Discussion
- Topic: Phase converter?
- Replies: 16
- Views: 5945
Re: Phase converter?
Lew, have you been to Mercury Tool lately?
- Fri Jun 20, 2003 9:51 pm
- Forum: Lathes
- Topic: Super 11" x 26" Bench Lathe - Belt Drive
- Replies: 2
- Views: 3097
Re: Super 11" x 26" Bench Lathe - Belt Drive
From looking at the spec. sheet it only cuts metric threads.