Search found 2066 matches
- Tue May 16, 2023 2:57 pm
- Forum: General Discussion
- Topic: Tapered taps
- Replies: 9
- Views: 1519
Re: Tapered taps
7/16 80 TPI ? That is quite a fine pitch for a 7/16 the tread is so small it won't take much taper before the threads disappear.
- Fri Apr 28, 2023 8:33 pm
- Forum: General Discussion
- Topic: 1/2” steel
- Replies: 6
- Views: 1636
Re: 1/2” steel
I have cut heavier than that and for longer run. 4.5" and the 7" are my only stock cutting tools.
- Fri Apr 28, 2023 8:00 pm
- Forum: Lathes
- Topic: How to cut NPT thread on manual lathe?
- Replies: 23
- Views: 8547
Re: How to cut NPT thread on manual lathe?
If it was me, and the pipe length was not so much to preclude the tail stock offset I would offset the tail stock and work between centers. Sure a purit can raise 1/2 dozen objections but if it gets the job done the plumbing dope can fill in the imperfection. The tool is perpendicular to the tube NO...
- Sun Mar 19, 2023 9:42 pm
- Forum: General Discussion
- Topic: Best tap for hard steel.
- Replies: 20
- Views: 30431
Re: Best tap for hard steel.
I stopped breaking taps after I got it through my head that after 3 or 4 threads the tap is not going to straighten and start cutting way too deep. Another thing is to use a thread percentage commensurate with hardness and number of engaged threads. No point in having the female thread many times st...
- Sun Mar 19, 2023 9:27 pm
- Forum: General Discussion
- Topic: Mystery Tool
- Replies: 6
- Views: 971
Re: Mystery Tool
Yes you can see the wire entering the tool end and exiting shortly after through the radial hole in the slot.
- Sun Mar 19, 2023 2:29 pm
- Forum: General Discussion
- Topic: Mystery Tool
- Replies: 6
- Views: 971
Re: Mystery Tool
Exactly. But can't figure how to use it, which is OK. My wire-wrapping days are over for good.
- Sun Mar 19, 2023 1:47 pm
- Forum: General Discussion
- Topic: Mystery Tool
- Replies: 6
- Views: 971
Mystery Tool
Anyone knows what this tool may be? The rest of handle looks like a watchmaker screwdriver. The wire is to show features. There is a small groove on top, the center hole 1s 1/2" deep, but the wire can surface at the milled-out slot. The point has a shallow counterbore before the small hole wher...
- Sat Mar 18, 2023 11:58 am
- Forum: General Discussion
- Topic: Best tap for hard steel.
- Replies: 20
- Views: 30431
Re: Best tap for hard steel.
Plan A Get some quality stock Plan B Try Annealing the spot or the entire part Plan C Gun Taps are 2 flutes and therefore the strongest, If the material is hard then 50% thread (larger hole) should make the job easier. Good tapping fluid is a must. I found Boelube is the best, is more than a wax tha...
- Sat Mar 04, 2023 4:06 pm
- Forum: General Discussion
- Topic: Starrett 98-6
- Replies: 7
- Views: 2790
Re: Starrett 98-6
Levels are probably the only instrument that can be adjusted/calibrate with no special tools.
Are you trying to "level" your lathe OR have doubt about whether the bubble is centered on a true horizontal surface and want to achieve such property.
The two task have different solutions.
Are you trying to "level" your lathe OR have doubt about whether the bubble is centered on a true horizontal surface and want to achieve such property.
The two task have different solutions.
- Sat Mar 04, 2023 12:53 pm
- Forum: I.C. Engines
- Topic: Rings Screw Up
- Replies: 9
- Views: 4567
Re: Rings Screw Up
Russ
If the grease method did not work, I was prepared to go into the spark plug hole with a 1/8 end mill and machine 0.060 off the visible piston top while rotating it freeing the ring.
If the grease method did not work, I was prepared to go into the spark plug hole with a 1/8 end mill and machine 0.060 off the visible piston top while rotating it freeing the ring.
- Sat Mar 04, 2023 8:33 am
- Forum: I.C. Engines
- Topic: Rings Screw Up
- Replies: 9
- Views: 4567
Re: Rings Screw Up
To tell the truth, never in my life. Gambling must be a genetic trait. I miss that gene.Did you pick up a lottery ticket ?
- Thu Mar 02, 2023 11:21 am
- Forum: I.C. Engines
- Topic: Rings Screw Up
- Replies: 9
- Views: 4567
Rings Screw Up
Is nice to celebrate one’s accomplishments but is more educational to share one’s failures. I was in the final fitting and assembly of my Anzani 3 cylinder radial. That engine has CI sleeves press fit into aluminum finned heads. Once mated the cylinder has only one way in but more to the point one w...