I have a set of CI main drivers, all bronze cylinders and a CI stack made by Tony Daddi a few decades ago.
These parts are a good start on kit bashing an A5.
Anyone interested? If so I can take / attach some pictures.
As much as I like this little engine, I doubt that I will live long enough to build one.
I will toss in a set of CAD drawings reworked from the Nusky originals
1-1/2" 0-4-0 Reading Camelback Misc Castings
Moderators: gwrdriver, Harold_V
- Bill Shields
- Posts: 10459
- Joined: Fri Dec 21, 2007 4:57 am
- Location: 39.367, -75.765
- Contact:
1-1/2" 0-4-0 Reading Camelback Misc Castings
Too many things going on to bother listing them.
Re: 1-1/2" 0-4-0 Reading Camelback Misc Castings
PM sent!
Best Steaming,
Ed Archer
Iron Horse Supply Corp.
www.ironhorsesupplycorp.com
ihsc775@gmail.com
ed.archer@ironhorsesupplycorp.com
Camelback #1173, 7-1/2" gauge, propane (a Leo M.'s build)
E6 #462 Atlantic (Saturated Steam), coal
3.2 scale 040 Vulcan 7-1/2 gauge, coal
12 ton 1936 040 Vulcan 2ft gauge, oil
"One with weak mind...Has strong legs"
Ed Archer
Iron Horse Supply Corp.
www.ironhorsesupplycorp.com
ihsc775@gmail.com
ed.archer@ironhorsesupplycorp.com
Camelback #1173, 7-1/2" gauge, propane (a Leo M.'s build)
E6 #462 Atlantic (Saturated Steam), coal
3.2 scale 040 Vulcan 7-1/2 gauge, coal
12 ton 1936 040 Vulcan 2ft gauge, oil
"One with weak mind...Has strong legs"
- Bill Shields
- Posts: 10459
- Joined: Fri Dec 21, 2007 4:57 am
- Location: 39.367, -75.765
- Contact:
Re: 1-1/2" 0-4-0 Reading Camelback Misc Castings
]I guess that there is more than a little interest, so I am going to post some pictures.
The cylinders, stack and driver are Daddi.
The remainder of the stuff is a mixture of Allen and Mercer (air tank brackets) circa middle 1980's
yes, there are only two eccentric castings but 6 bronze eccentric strap sets (go figure)…
I think I was going to use them to drive my dual axle pump and went a different direction and used bar stock instead.
The drivers are back turned and bored to 1.0" (done by Daddi)
3 of the tender wheels are rough worked, the remainder are raw castings.
I really want to sell the entire lot to one person if at all possible.
bshields at mehrs dot com
The cylinders, stack and driver are Daddi.
The remainder of the stuff is a mixture of Allen and Mercer (air tank brackets) circa middle 1980's
yes, there are only two eccentric castings but 6 bronze eccentric strap sets (go figure)…
I think I was going to use them to drive my dual axle pump and went a different direction and used bar stock instead.
The drivers are back turned and bored to 1.0" (done by Daddi)
3 of the tender wheels are rough worked, the remainder are raw castings.
I really want to sell the entire lot to one person if at all possible.
bshields at mehrs dot com
Last edited by Bill Shields on Wed Oct 17, 2018 8:08 pm, edited 2 times in total.
Too many things going on to bother listing them.
- Bill Shields
- Posts: 10459
- Joined: Fri Dec 21, 2007 4:57 am
- Location: 39.367, -75.765
- Contact:
Re: 1-1/2" 0-4-0 Reading Camelback Misc Castings
More pictures
Too many things going on to bother listing them.
- Bill Shields
- Posts: 10459
- Joined: Fri Dec 21, 2007 4:57 am
- Location: 39.367, -75.765
- Contact:
Re: 1-1/2" 0-4-0 Reading Camelback Misc Castings
More
Too many things going on to bother listing them.