External turning with a boring head
External turning with a boring head
With a boring head, one can bore holes of any size. I have seen where one can turn an external diameter using a boring head, but the cutting bits cannot be reversed to cut externally. I would think bits would be available to do external turning, but I can't find anything anywhere. Is there such a thing?
Mr.Ron from South Mississippi
-
- Posts: 532
- Joined: Thu May 30, 2013 4:40 am
Re: External turning with a boring head
Use a left hand boring bar or reverse your mill!
Re: External turning with a boring head
I searched through the MSC catalog on line, but did not see any left hand bars. I noticed they were listed as "right hand cut", but could not find any listed as "left hand cut".
Richard_W; Those left hand bars are for the cross hole in the head. I want the left hand bars that operate in the vertical position.
Richard_W; Those left hand bars are for the cross hole in the head. I want the left hand bars that operate in the vertical position.
Mr.Ron from South Mississippi
- warmstrong1955
- Posts: 3568
- Joined: Thu Mar 18, 2010 2:05 pm
- Location: Northern Nevada
Re: External turning with a boring head
LH available here, and I have some: http://www.mesatool.com/products/boring-bars/
Good tools. I have many from Mesa.
Bill
Good tools. I have many from Mesa.
Bill
Today's solutions are tomorrow's problems.
- tornitore45
- Posts: 2077
- Joined: Tue Apr 18, 2006 12:24 am
- Location: USA Texas, Austin
Re: External turning with a boring head
My boring head has a threaded shank and could not be run in reverse.
I drilled a hole at a convenient angle to intercept the shank thread almost tangentially then tapped the hole, then milled a divot on the shank thread where the set screw would touch. The set screw hold the tread from unscrewing. Now I run the boring head in reverse with the usual RH boring bar. Cheaper than a LH boring bar to be rarely used.
I drilled a hole at a convenient angle to intercept the shank thread almost tangentially then tapped the hole, then milled a divot on the shank thread where the set screw would touch. The set screw hold the tread from unscrewing. Now I run the boring head in reverse with the usual RH boring bar. Cheaper than a LH boring bar to be rarely used.
Mauro Gaetano
in Austin TX
in Austin TX
Re: External turning with a boring head
Think about it some more. Some times things are hard to visualize. I have used left hand boring bar on the lathes. Both CNC and manual. They will work just fine for turning an O.D. with a boring head in the vertical position. I have done it. Usually on larger parts on an HBM with a boring head.
You are right that they will work fine out the side hole. I have done that to.
Richard W.
Re: External turning with a boring head
A bit of lockite on the threads will solve the problem of not being able to run in reverse. Heating the head can destroy the bond so you can later unscrew it if necessary.tornitore45 wrote: ↑Wed Feb 07, 2018 3:12 pm My boring head has a threaded shank and could not be run in reverse.
I drilled a hole at a convenient angle to intercept the shank thread almost tangentially then tapped the hole, then milled a divot on the shank thread where the set screw would touch. The set screw hold the tread from unscrewing. Now I run the boring head in reverse with the usual RH boring bar. Cheaper than a LH boring bar to be rarely used.
Re: External turning with a boring head
The shortest one is 3" long; too long to be used vertically; that was designed for use in the horizontal cross hole. My mill doesn't reverse and the head is screwed onto the shank.warmstrong1955 wrote: ↑Wed Feb 07, 2018 2:33 pm LH available here, and I have some: http://www.mesatool.com/products/boring-bars/
Good tools. I have many from Mesa.
Bill
Mr.Ron from South Mississippi
Re: External turning with a boring head
I could turn the diameter on the lathe, but sometimes you may have a setup on the mill which may require a diameter feature to be incorporated. It is more precise to do all machining operations with one setup. It's like having a 4 axis machining center.
Mr.Ron from South Mississippi
- warmstrong1955
- Posts: 3568
- Joined: Thu Mar 18, 2010 2:05 pm
- Location: Northern Nevada
Re: External turning with a boring head
Is 3" too long due to the size of your mill? I have RH bars from 3" to 8", which I have used vertically, for ID's of course.
If you are turning the OD, the machine will need to be turning forward if you use a LH bar.
Bill
If you are turning the OD, the machine will need to be turning forward if you use a LH bar.
Bill
Today's solutions are tomorrow's problems.
-
- Posts: 187
- Joined: Tue Dec 04, 2007 11:00 am
- Location: Ivins, Utah
Re: External turning with a boring head
Careful, here. After thorough cleaning, using 'red' loctite and allowing full cure, the shank on my boring head came loose running in reverse on what amounted to an interrupted cut while taking off the high spots on the part. It worked fine after it was all round though.