Ball Screw Pitch
Moderator: Harold_V
Ball Screw Pitch
Setting up a lathe for CNC and was wondering if ball screw pitch can be different between the Z axis (5MM) and X axis (4MM). Had to get a smaller ball screw for my X to physically make it fit and found out it was 4MM pitch.
Re: Ball Screw Pitch
I believe this would be addressed in your controller software - which one are you using?.
Standards are so important that everyone must have their own...
To measure is to know - Lord Kelvin
Disclaimer: I'm just a guy with a few machines...
To measure is to know - Lord Kelvin
Disclaimer: I'm just a guy with a few machines...
Re: Ball Screw Pitch
Yes, Mach 3 will let you set up each axis with different leads or different motors. It is calculated in the turns per inch entry if your are using imperial setups. If you are setting up a metric setup it wants distance of travel per one turn of the motor.
So a .200" lead would be 5 tuns per inch and so on. You can use metric ball screws and still set up your machine as "inches" but you'll have to do some extra math.
Dave C.
So a .200" lead would be 5 tuns per inch and so on. You can use metric ball screws and still set up your machine as "inches" but you'll have to do some extra math.
Dave C.
I learn something new every day! Problem is I forget two.
- SteveHGraham
- Posts: 7788
- Joined: Sat Jan 17, 2009 7:55 pm
- Location: Florida
Re: Ball Screw Pitch
Wow. A CNC question I could have answered.
Every hard-fried egg began life sunny-side up.
Re: Ball Screw Pitch
Thanks for the help guys its been a fun build so far and sorry if I ask some scary questions?? lol
Re: Ball Screw Pitch
I'd second that, even though I am still running a Mach 3 lathe conversion. Centroid is Funac compatible and runs a full set of G-codes while Mach 3 runs a partial set and is not compatible with anything else, as far as I'm aware. You will need a spindle encoder, a real one and not just the indexing type like mach uses, if you want to thread or do rigid tapping with the Acron/Centroid setup.
I'm in the process of reading the entire manual right now for the Centroid lathe and mill software. It is written very well, more like the way I understand tech manuals.
Dave C.
I'm in the process of reading the entire manual right now for the Centroid lathe and mill software. It is written very well, more like the way I understand tech manuals.
Dave C.
I learn something new every day! Problem is I forget two.
- Bill Shields
- Posts: 10582
- Joined: Fri Dec 21, 2007 4:57 am
- Location: 39.367, -75.765
- Contact:
Re: Ball Screw Pitch
actually you want an encoder WITH a zero pulse index point so that you can reliably find home every time.
Too many things going on to bother listing them.
Re: Ball Screw Pitch
Ok, My poor explanation! Mach 3 uses a single slot spindle index and nothing else. So basically you make a disc with one slot in it, use an optical reader to read the slot or you can use one of those other type single pulse per rev encoders like a photo tac.
Mach 3 can't read a real 2000 line encoder for spindle positioning. Mach 3 also can't use CSS and FPR at the same time. (constant surface speed and Feed per Rev) One or the other but not both!
So no rigid tapping!
Dave C.
Mach 3 can't read a real 2000 line encoder for spindle positioning. Mach 3 also can't use CSS and FPR at the same time. (constant surface speed and Feed per Rev) One or the other but not both!
So no rigid tapping!
Dave C.
I learn something new every day! Problem is I forget two.
Re: Ball Screw Pitch
I'd have to spring for the Centroid Pro CNC. Looks like an interesting solution.
Standards are so important that everyone must have their own...
To measure is to know - Lord Kelvin
Disclaimer: I'm just a guy with a few machines...
To measure is to know - Lord Kelvin
Disclaimer: I'm just a guy with a few machines...
-
- Site Admin
- Posts: 1730
- Joined: Wed Dec 18, 2002 8:17 pm
- Location: Mesa, AZ USA
Re: Ball Screw Pitch
You WON'T be dissappointed!ctwo wrote:I'd have to spring for the Centroid Pro CNC. Looks like an interesting solution.
Marty
"Jack of all Trades, Master of None"