Polishing Aluminum

Topics include, Machine Tools & Tooling, Precision Measuring, Materials and their Properties, Electrical discussions related to machine tools, setups, fixtures and jigs and other general discussion related to amateur machining.

Moderators: GlennW, Harold_V

Phil3
Posts: 193
Joined: Tue Oct 05, 2010 7:33 pm
Location: San Ramon, CA

Polishing Aluminum

Post by Phil3 »

How does one obtain a smooth finish on an aluminum part produced on a milling machine? As an example, a 2" cube of aluminum with a 1/2" notch cut along one side, where all surfaces need to be aesthetically pleasing with minimal machine marks. A four flute end mill does well, but if I wanted a polished surface, what methods and how to get into inside corners or angles?

- Phil
JimGlass
Posts: 2281
Joined: Sat Jan 04, 2003 8:33 pm
Location: 40 Miles West of Chicago/near DeKalb
Contact:

Re: Polishing Aluminum

Post by JimGlass »

A fly cutter works good for this. Use a toolbit with generous tool nose radius. Your milling machine head will need to be square as possible to the table.

Jim
Tool & Die Maker/Electrician, Retired 2007

So much to learn and so little time.

www.outbackmachineshop.com
RSG
Posts: 1541
Joined: Fri Feb 04, 2011 9:59 am
Location: Ontario, Canada

Re: Polishing Aluminum

Post by RSG »

Not sure just how fine a finish you are looking for but I haven't found a method yet that doesn't require allot of fine sanding with various grits down to 1000 grit then its off the vibrartory chamber in corn cob media then fine walnut. As Phil3 mentions having a mill square and trammed to the table is a good start.
Vision is not seeing things as they are, but as they will be.
Conrad_R_Hoffman
Posts: 440
Joined: Wed May 24, 2006 8:40 am
Location: Canandaigua, NY
Contact:

Re: Polishing Aluminum

Post by Conrad_R_Hoffman »

Similar to a flycutter, those expensive insert cutters about 3.5" diameter with 8 or so inserts give almost a mirror finish. My guess is buffing would be short work after that, though I find the finish very nice as is.
Conrad

1947 Logan 211 Lathe, Grizzly G1006 mill/drill, Clausing DP,
Boyar-Schultz 612H surface grinder, Sunnen hone, import
bandsaw, lots of measurement stuff, cutters, clutter & stuff.


"May the root sum of the squares of the Forces be with you."
david5605
Posts: 205
Joined: Sat Feb 16, 2008 10:40 am
Location: Raleigh, NC

Re: Polishing Aluminum

Post by david5605 »

Something that size you can throw in a rock tumbler with the correct grit and let it tumble for a day or two. The tumbler will polish it but will not remove any milling marks. All it will do is polish them up.

I've used the tumbler on some aluminum turners cubes I made with good results. It does get in to all the nooks and crannies.
Orrin
Posts: 307
Joined: Sat Jan 04, 2003 12:24 pm
Location: SE Washington State, near Moscow, Idaho

Re: Polishing Aluminum

Post by Orrin »

I realize my technique is not always possible or practical; but, when it will work in your situation I recommend it.

I use a HSS fly-cutter on aluminum whenever possible. The edge is as keen as possible. I always brush on kerosene, never allowing the cutting edge become dry.

I never touch the aluminum, afterward, with bare hands. I always wear soft cotton gloves or use facial tissue to handle the part. The reward is a brilliant surface that looks somewhat like a CD and causes refractions that are all colors of the rainbow.

When this isn't possible, I buff out machine markings with Cratex tips, followed by polishing with any kind of brightwork polish. I remove the residue with kerosene, followed by a wipe-down with denatured alcohol, all the while making sure my hands never touch the aluminum.

I used these methods in building my Miser engine, seen here:

http://users.moscow.com/oiseming/lc_ant_p/pic_Prj2.htm

At one meet an old-timer took a look, snorted, then stomped off, accusing me of taking things a bit too far by having the flywheel chrome-plated.

Orrin
So many projects, so little time.
User avatar
seal killer
Posts: 4696
Joined: Sat Aug 18, 2007 10:58 pm
Location: Ozark Mountains

Re: Polishing Aluminum

Post by seal killer »

Orrin and Phil and All--

Getting a great finish on aluminum was a difficult task for me. I finally managed to get an acceptable result after using 1000, 1200, then 1500 grit wet/dry. Next, I moved to the buffing wheel and used Tripoli 327 and finished with Jeweler's Rouge. I learned to dedicate a wheel to each different buffing compound . . . never mix them.

Perhaps, if I had known what I was doing, I may have been able to eliminate the 1200 and 1500 grit sandpaper. Still, the aluminum turned out pretty good.

--Bill
You are what you write.
RSG
Posts: 1541
Joined: Fri Feb 04, 2011 9:59 am
Location: Ontario, Canada

Re: Polishing Aluminum

Post by RSG »

Looks pretty good Bill, some wax will help keep that shine too. Before I ever started anodizing my own stuff I did a buff polish like yours. Keeping it shiny was easy with wax.
Vision is not seeing things as they are, but as they will be.
User avatar
steamin10
Posts: 6712
Joined: Sun Jun 08, 2003 11:52 pm
Location: NW Indiana. Close to Lake Michigan S. tip

Re: Polishing Aluminum

Post by steamin10 »

Aluminum oxidizes very quickly, and usually, any chemicals cause moisture to destroy the surface luster. I have been curious about home anodizing, as opposed to clear coat painting.

Is there any doable information out there?
Big Dave, former Millwright, Electrician, Environmental conditioning, and back yard Fixxit guy. Now retired, persuing boats, trains, and broken relics.
We have enough youth, how about a fountain of Smart. My computer beat me at chess, but not kickboxing
It is not getting caught in the rain, its learning to dance in it. People saying good morning, should have to prove it.
roundnose
Posts: 103
Joined: Thu Nov 11, 2010 4:21 pm

Re: Polishing Aluminum

Post by roundnose »

For perhaps a little humor, though some may not find it real funny.
Through the 90s, I made considerable profit doing a final polish in the combustion chambers in motorcycle cylinder heads.
This was after flow balancing the ports. working the valves and seats," the real work".
This polishing is not always the best thing to do, on higher compression engines the polished surface can cause a heat barrier, reducing the cylinder heads ability to absorb heat, and can cause a piston to burn.
I found I could not get that point across to a majority of customers.
So, often I had to polish them up, so the customer could see them and feel good, then on engine assembly, I would rough up the polished surface to prevent over heating and engine failure.
Bikers are like bower birds, they like shiny things.

To get this polish. The final two steps, by hand, use 600 wet/dry paper with WD 40. Last- Mothers polish and a flannel rag.
The steel valve heads were done on a lathe.

http://s170.photobucket.com/albums/u265 ... bay006.jpg

I dont know if this is a tip or a confession!
User avatar
seal killer
Posts: 4696
Joined: Sat Aug 18, 2007 10:58 pm
Location: Ozark Mountains

Re: Polishing Aluminum

Post by seal killer »

roundnose--

I don't know if it's a tip or a confession, either. I do know it is beautiful work! Can you do my bling-bling Sportster? Chrome makes it run faster, so polishing the combustion chambers will, also! :)

--Bill
You are what you write.
roundnose
Posts: 103
Joined: Thu Nov 11, 2010 4:21 pm

Re: Polishing Aluminum

Post by roundnose »

Straying off the subject.
The best gains on Harleys, is on the heads, not a bad design, but terribly executed in manaufacturing.
Nothing lines up, the manifold to head interface, valve seat edges poking into the ports, shrouding of the seats from the head casting in the combustion chamber, CC volume difference in both heads, the worst in the industry.
Take care of that mess, will go along way in over all running of the engine.
The object being to reduce port turbulence, causing a bad fuel mix resulting in detonation. This by increasing fuel mix velocity when the valve first cracks open, and on through the valve cycle.

One of my favorite photos from those profitable days.

http://s170.photobucket.com/albums/u265 ... ots017.jpg

Oh ya. it only took money, a plenty of it, to fix that disaster.
I know, I have a bad attitude!
Post Reply