Search found 25 matches
- Fri Apr 16, 2021 6:56 pm
- Forum: General Discussion
- Topic: single phase shaded pole motor reversal question
- Replies: 6
- Views: 4041
Re: single phase shaded pole motor reversal question
Many posts and info on the web it seems these motors run very hot because of the shaded pole components. It also seems they require constant air flow so they don't overheat. Based on that I don't think they would be appropriate for a mini lathe.
- Fri Apr 16, 2021 12:24 pm
- Forum: General Discussion
- Topic: single phase shaded pole motor reversal question
- Replies: 6
- Views: 4041
single phase shaded pole motor reversal question
My motor rotates in the wrong direction for my application and I've read this type of motor is non-reversible. However I've found some youtube videos that show the rotation can be reversed by removing the end caps, pulling out the rotor and reinstalling the rotor such that the shaft is at the opposi...
- Thu Apr 15, 2021 5:37 pm
- Forum: General Discussion
- Topic: AC 115v single phase 4 lead motor question
- Replies: 3
- Views: 3385
Re: AC 115v single phase 4 lead motor question
Thanks Victor_R. The wire that looks brown, on my motor, is the bare copper ground wire connected to the frame. The motor with unused leads joined was just something I ran across, which led me to ask if unused leads on my motor, should be connected or not. I checked the ohm value of the 3 leads and ...
- Thu Apr 15, 2021 12:49 pm
- Forum: General Discussion
- Topic: AC 115v single phase 4 lead motor question
- Replies: 3
- Views: 3385
AC 115v single phase 4 lead motor question
I just got a NOS Shaded pole split phase motor and I believe it is a three speed motor. The leads are black, blue, red and white and I think wiring scheme is neutral line goes to white lead and hot line is connected to any one of the other three leads for low, medium or high speed. My question is ar...
- Sun Mar 21, 2021 11:07 am
- Forum: Lathes
- Topic: brushless DC motor for mini lathe
- Replies: 0
- Views: 8461
brushless DC motor for mini lathe
I need a new motor for my Boley Leinen 8mm lathe and my web searches have led me to thinking brushless DC motors have very good characteristics for mini lathes. Is anyone here using one on their lathes and if so, what brand?
Thanks,
henryr
Thanks,
henryr
- Tue Mar 16, 2021 3:06 pm
- Forum: Lathes
- Topic: Watchmakers lathe accuracy
- Replies: 3
- Views: 5146
Watchmakers lathe accuracy
This may be hard to believe but the Boley Leinen 8mm lathe, I've owned for 15 years has amazing, to me, spindle runout accuracy. About 5 five years ago I measured the spindle runout, starting with a last word indicator with .001 divisions and the indicator never moved. I switched to a .0005 division...
- Fri Mar 12, 2021 10:17 am
- Forum: General Discussion
- Topic: tapered roller bearings
- Replies: 17
- Views: 8936
Re: tapered roller bearings
I emailed many distributors, in the US, UK and Japan and Timken, SKF and Nachi technical support, and all told me they only make tapered roller bearings in the lowest tolerance class like 0 or K. It seems there is one company, Gamet, that makes them but cost is around $1000 for one bearing. So i'm c...
- Thu Mar 11, 2021 10:38 am
- Forum: General Discussion
- Topic: tapered roller bearings
- Replies: 17
- Views: 8936
Re: tapered roller bearings
Seems that angular contact bearings and ABEC bearings are not made in the same dimensions of metric tapered roller bearings.
- Tue Mar 09, 2021 6:46 pm
- Forum: General Discussion
- Topic: tapered roller bearings
- Replies: 17
- Views: 8936
tapered roller bearings
I’ve spent hours over the last three days looking for tapered roller bearings with tighter than normal tolerances and didn’t find any. Timken and SKF sites list tapered roller bearings with standard and tighter tolerances but I couldn’t find any. So I spoke with their technical support people and wa...
- Fri Mar 05, 2021 7:13 pm
- Forum: Lathes
- Topic: Prazi carriage stop
- Replies: 2
- Views: 4579
Re: Prazi carriage stop
here are a few more pics
- Fri Mar 05, 2021 7:01 pm
- Forum: Lathes
- Topic: Prazi carriage stop
- Replies: 2
- Views: 4579
Prazi carriage stop
So after making the handles it seemed time to make a carriage lock. Here are pics and dimensioned drawings. The round black locking pads are a very hard plastic that I tapped to accept 10-24 screw threads. After tapping them I put super glue around the edge of the cover and closed it so when they ge...
- Mon Mar 01, 2021 11:19 am
- Forum: Lathes
- Topic: Prazi SD300 lathe locking handles
- Replies: 0
- Views: 7446
Prazi SD300 lathe locking handles
I got tired of using the M6 allen wrench to lock and unlock the carriage and tailstock on my Prazi SD300 lathe so I designed and made locking handles. They work great so I thought others may want to make them. Here are some pics, dimensioned drawings and mounting instructions. Handle mounting steps:...