Search found 492 matches
- Thu Jun 29, 2023 1:03 pm
- Forum: Live Steam Marketplace
- Topic: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
- Replies: 7
- Views: 2215
Re: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
To add to that, a notable number of people have asked which pipe size they should use if they haven’t tapped their steam dome yet. It really does not matter and is entirely a matter of preference. The hole through the center of the adapter is the same diameter on every size, and the pipe thread has ...
- Thu Jun 29, 2023 12:30 am
- Forum: Live Steam Marketplace
- Topic: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
- Replies: 7
- Views: 2215
- Wed Jun 28, 2023 7:48 pm
- Forum: Live Steam Marketplace
- Topic: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
- Replies: 7
- Views: 2215
Re: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
Safety valve project is nearly complete. All that’s left to do is square up the springs and finish the boiler adapters. I expect to start shipping valves next week after 4th of July. Now would be a good time to order if you’re interested! https://www.eccentricengineer.com/safety-valves IMG_9939.jpeg
- Sat Jun 17, 2023 10:13 am
- Forum: Live Steam
- Topic: Snifter valves and cylinder lubricator hardware vendors?
- Replies: 10
- Views: 4010
Re: Snifter valves and cylinder lubricator hardware vendors?
Just FYI, I'm working on making straight and angled check valves in 5/16, 1/4, 3/16, 5/32, and 1/8 MTP. Hope to have them ready by August.
Anthony
Anthony
- Fri May 12, 2023 7:36 pm
- Forum: Live Steam
- Topic: Who makes "snap on-off" valves?
- Replies: 11
- Views: 4011
Re: Who makes "snap on-off" valves?
Will EE have the injector starting valves in stock any time soon? I hope to make more sooner rather than later. My plate is pretty full at the moment though! I will also be looking into making a 1/4 turn injector starting globe valve to go along with the globe valve project. It would be a standard ...
- Sat May 06, 2023 12:58 am
- Forum: Live Steam
- Topic: Who makes "snap on-off" valves?
- Replies: 11
- Views: 4011
Re: Who makes "snap on-off" valves?
Personally I would highly recommend a 1/4 turn valve over a quick on/off valve. They are just as fast to operate, but can still be cracked open which helps with priming in less desirable scenarios, like a leaky check valve or hot feedwater.
- Tue May 02, 2023 10:08 am
- Forum: Live Steam Marketplace
- Topic: 1.6" and 2.5" Safeties Expected Late June - Preorders Available
- Replies: 7
- Views: 2215
1.6" and 2.5" Safeties Expected Late June - Preorders Available
Hi all, I'm pleased to let you know that the 1.6” and 2.5” safety valves are now available for pre-order! Current estimated delivery date is late June. 1.6" Safeties can be pre-ordered here: https://www.eccentricengineer.com/safety-valves/16-scale-consolidated-safety-valve And the 2.5" Sca...
- Mon Feb 20, 2023 12:31 pm
- Forum: Live Steam
- Topic: A good reliable injector for inch & half scale that works ????
- Replies: 34
- Views: 8333
Re: A good reliable injector for inch & half scale that works ????
Hi Fender If this is a superscale injector, where is this washer located, and how should it be facing. Maybe that is also the problem. The locomotive I am talking about, was build by WLS member Don Cornell, and 0-4-2 the Locomotive has side water tanks, no Tender. As I said I will post photos of th...
- Sat Feb 18, 2023 11:32 am
- Forum: Live Steam
- Topic: A good reliable injector for inch & half scale that works ????
- Replies: 34
- Views: 8333
Re: A good reliable injector for inch & half scale that works ????
Not starting until 60psi is most likely due to a very minuscule air leak between the water valve and injector. Air leak symptoms typically improve at higher pressure rather than worsen. However, cutting out at 80psi is a bit more unusual. The only things that could cause this in order of likelihood ...
- Fri Feb 17, 2023 3:47 pm
- Forum: Live Steam
- Topic: A good reliable injector for inch & half scale that works ????
- Replies: 34
- Views: 8333
Re: A good reliable injector for inch & half scale that works ????
If the injector on there is truly a SuperScale injector it should work fine from 40-150psi. If it’s only working from 60-80psi then there is a problem somewhere somehow with the installation.
- Mon Feb 06, 2023 2:19 pm
- Forum: Live Steam Marketplace
- Topic: "Free Flow" boiler check valves from EE
- Replies: 9
- Views: 4130
Re: "Free Flow" boiler check valves from EE
A "future product" page has been added for check and globe valves! https://www.eccentricengineer.com/globe-check-valves If you are interested in these it would be greatly appreciated if you could take the time to fill out the form at the bottom of the linked page! This will be a monumental...
- Sat Jan 28, 2023 6:11 pm
- Forum: Live Steam
- Topic: Nathan double top check boiler feed valve
- Replies: 35
- Views: 11212
Re: Nathan double top check boiler feed valve
So why does the feedwater heater take a different check than the injector? The pump side is a bit more complicated to help reduce losses from the repeated hammering of the check valve. Larger diameter, less valve lift, a longer valve guide, and a spring all help reduce losses every time the valve c...