Search found 1002 matches
- Mon Dec 29, 2014 9:45 pm
- Forum: General Discussion
- Topic: Storing Dies
- Replies: 4
- Views: 2128
Re: Storing Dies
That looks like a good idea already. The only other things I can think of would be semi-circular grooves or troughs in a thick piece of wood or shallow round holes in a piece of wood.
- Mon Dec 29, 2014 9:30 pm
- Forum: Lathes
- Topic: Allen lathe
- Replies: 5
- Views: 3142
Re: Allen lathe
Although made for turning armature commutators, that lathe will do general lathe work with the exception of threading. I am not sure but it looks like the power feed disconnect may be the long collar near the left end of the leadscrew. If that chuck in the tailstock is the Jacobs armature chuck with...
- Tue Dec 23, 2014 9:19 pm
- Forum: Lathes
- Topic: Need Advice for missing compound on cross feed
- Replies: 24
- Views: 6598
Re: Need Advice for missing compound on cross feed
I can't tell much else but the taper attachment seems to be missing the block which slides along the bar. In one type of attachment this block is connected to the cross slide by a slotted arm and lock bolt which provides coarse adjustment of the slide position. This type requires a separate compound...
- Tue Dec 23, 2014 9:04 pm
- Forum: The Junk Drawer
- Topic: Merry Christmas
- Replies: 6
- Views: 1927
Re: Merry Christmas
My Christmas will certainly be Merry and I hope all others will be too. (Including Scrooges and Grinches. )
- Sun Dec 21, 2014 10:38 pm
- Forum: Lathes
- Topic: Need Advice for missing compound on cross feed
- Replies: 24
- Views: 6598
Re: Need Advice for missing compound on cross feed
I got the idea that you may be concerned about manual fine feeding toward the chuck for facing type work. It is not very convenient but you can lock the half-nuts onto the leadscrew and use the leadscrew for fine feeding. If it has an accessible gear on it, you can even calculate how much feed you g...
- Sun Dec 21, 2014 10:25 pm
- Forum: Milling Machines
- Topic: Y-axis help
- Replies: 19
- Views: 5975
Re: Y-axis help
Actually you would only have to insulate the wiper motor from the chassis if one of the power supply terminals is permanently connected to the chassis also. Otherwise the power supply leads could be easily reversed (ground either negative or positive). I would think a dedicated power supply would be...
- Fri Nov 21, 2014 9:59 pm
- Forum: Lathes
- Topic: clausing colchester VS 12-36
- Replies: 9
- Views: 4793
Re: clausing colchester VS 12-36
Looks good!
- Fri Nov 21, 2014 9:41 pm
- Forum: Milling Machines
- Topic: Bridgeport M head new old info
- Replies: 7
- Views: 2745
Re: Bridgeport M head new old info
I don't know about M heads but some J heads certainly came with sealed spindle bearings.
- Thu Nov 06, 2014 10:24 pm
- Forum: Welding
- Topic: Tack Broken Bolt in Aluminum
- Replies: 18
- Views: 10452
Re: Tack Broken Bolt in Aluminum
I agree with Glenn on the hammer and punch. If you can jar the bolt lengthwise hard enough it nearly always loosens without damage. For Allen type fasteners I prefer a steel punch down in the socket. I like to hit it really hard with a heavy hammer like I am trying to drive it out. The air hammer of...
- Sat Oct 25, 2014 8:15 pm
- Forum: The Junk Drawer
- Topic: Never enough time
- Replies: 1881
- Views: 370354
Re: Never enough time
Dual fuel, diesel and natural gas, engines have been used in power plants for at least 50 years. The Safeguard Anti-Missile system used several Cooper Bessemer LSV-16 engines so equipped. They were approximately 5000 HP at 360 RPM. They started on diesel, then a control started injecting gas into th...
- Sun Oct 19, 2014 8:01 pm
- Forum: Lathes
- Topic: What's this bit about?
- Replies: 12
- Views: 6725
Re: What's this bit about?
I have no idea what they are but they look uniform in thickness and all seem to have the notch so I don't think they are made from knife blades. The notch seems to be a functional feature to me. It kinda looks like there may have been some sort of writing on them.
- Mon Oct 13, 2014 7:59 pm
- Forum: Welding
- Topic: Small Welding torch
- Replies: 15
- Views: 11235
Re: Small Welding torch
Some, if not most, torch leaks are after the valves so they leak only when the valves are open.chooch wrote:OK. Why can`t you just turn on the tanks, torches OFF and dunk the torch in a bucket of plain ole` water?
chooch