Search found 277 matches
- Fri Mar 12, 2021 2:21 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: New G9729 - Some early issues.
- Replies: 26
- Views: 37391
Re: New G9729 - Some early issues.
No problem running the ShopTask models with the doors/hatches open as there are no electrical "interlocks." I did make and add table limit switches after the first time I used the power feed and it snapped the spline shaft when the scale on the table hit +4-1/2" even though the table ...
- Thu Mar 04, 2021 3:09 pm
- Forum: General Discussion
- Topic: Drilling Through Holes on the Mill
- Replies: 12
- Views: 9759
Re: Drilling Through Holes on the Mill
I just milled a through slot in a piece of copper strap. I first milled a piece of scrap wood to the same thickness as the width of the strap. Then I used double sided tape to secure the strap to the wood and placed the whole thing into the milling vice, (below the jaws) and milled down into the woo...
- Sun Feb 14, 2021 3:35 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: What size milling vise for my Lathe/ Mill?
- Replies: 8
- Views: 13922
Re: What size milling vise for my Lathe/ Mill?
I use a 4" Shars. I paid $100. It is no KURT. There is a very slight difference in tightness from one side to the other (annoying), but perhaps a bit of sand paper tugged between the jaws could fix this.
- Fri Jan 08, 2021 2:37 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
- Wed Jan 06, 2021 3:27 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
Re: VFD to 2 motors
If the original poster isn't interested in the VFD, I would be. Steve I got a TECO JNEV-101-H1 brand new when I got my machine. But it doesn't have the capacity for my machine and has been on the shelf ever since. Is this something you could use? (1HP/750 Watt) Just like this one: https://dealersel...
- Mon Jan 04, 2021 2:11 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
Re: VFD to 2 motors
I got a TECO JNEV-101-H1 brand new when I got my machine. But it doesn't have the capacity for my machine and has been on the shelf ever since. Is this something you could use? (1HP/750 Watt) Just like this one: https://dealerselectric.com/JNEV-101-H1.asp https://dealerselectric.com/images/products/...
- Fri Jan 01, 2021 2:05 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
Re: VFD to 2 motors
Should only need two contactors. Go on ebay and look for three pole contactors. Chinese pieces are <$10 each. American quality may cost a few dollars more. I can't imagine that you would need to switch more than 20 amps, but you can easily find them that can handle over twice this current. These are...
- Thu Dec 31, 2020 3:48 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
Re: VFD to 2 motors
After a bit of thought..., cheapest and easiest way to go with no concerns for power handling, because you can get big-azz contactors fairly cheap. Use two three pole contactors. They can be low voltage with a wall wart, or full 120 or 240 volt. Use a dpdt center off toggle switch to send power to w...
- Thu Dec 31, 2020 2:47 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: Shoptask owners?
- Replies: 68
- Views: 98189
Re: Shoptask owners?
So glad it worked for you, and now I know that if I have the problem with mine, I can rectify it. You owe me a steak.
I assume that you saw the threading instructions that I posted?
I assume that you saw the threading instructions that I posted?
- Thu Dec 31, 2020 2:38 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: VFD to 2 motors
- Replies: 27
- Views: 36339
Re: VFD to 2 motors
Thanks. Any suggestions on a 3P2T switch? Don't use a switch. Use a 12 volt contactor and use a wall wart to switch that. That's how I did my table limit switches. In fact, I never switch the forward/reverse "on switch" for either the lathe or mill when live. I always leave the contactor ...
- Wed Dec 30, 2020 5:10 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: Threading on Shoptask Gold Machine
- Replies: 13
- Views: 20842
Re: Threading on Shoptask Gold Machine
Here you go: https://cimg4.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/580x435/80-threading_004_3b6da8f2cea0f71737b23090ed49c6973bd5e361.jpg https://cimg7.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/580x435/80-threading_002_50deb697894628f8197fa9934633696bfc5b1fb7.jpg https://cimg8.ibsrv.net/g...
- Wed Dec 30, 2020 2:38 pm
- Forum: 3-in-1 Metalworking Machines
- Topic: Threading on Shoptask Gold Machine
- Replies: 13
- Views: 20842
Re: Threading on Shoptask Gold Machine
See below: