Bill and Glenn and dorin--
Gentlemen, Thank you!
--Bill
Search found 4694 matches
- Sun Jan 08, 2023 10:28 am
- Forum: General Discussion
- Topic: CAD Software -- free
- Replies: 20
- Views: 4129
- Sat Jan 07, 2023 5:57 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Re: Help Identify Tool Chests
Tom-- Here is a link to the the thread and picture of the machinist chest I restored using a LOT of help from this forum's members. The picture shows a good view of the (missing) front cover I had to build for it. (Just scroll down about three posts.) https://www.chaski.org/homemachinist/viewtopic.p...
- Sat Jan 07, 2023 5:48 pm
- Forum: General Discussion
- Topic: CAD Software -- free
- Replies: 20
- Views: 4129
CAD Software -- free
All--
Do you use any free CAD software? How do you like it?
--Bill
Do you use any free CAD software? How do you like it?
--Bill
- Sat Jan 07, 2023 1:14 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Re: Help Identify Tool Chests
Tom-- I restored a chest some time ago. Building a front cover is relatively easy. Some of the older chests are worth surprising amounts. The one I restored is almost identical to this one . . . https://www.1stdibs.com/furniture/storage-case-pieces/cabinets/antique-eight-drawer-oak-machinists-chest-...
- Fri Jan 06, 2023 1:37 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Re: Help Identify Tool Chests
jcfx--
They are not mine. I'm trying to help a friend figure out if there is any value in any of them. I think there may be with the top case.
But I am not sure.
--Bill
They are not mine. I'm trying to help a friend figure out if there is any value in any of them. I think there may be with the top case.
But I am not sure.
--Bill
- Thu Jan 05, 2023 10:00 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Re: Help Identify Tool Chests
All--
I found the B*B cases at online auctions. They are inexpensive watchmakers chests. I found two; $65 and $75.
But how about that top chest? It looks like a machinist chest for sure. What do you think?
--Bill
I found the B*B cases at online auctions. They are inexpensive watchmakers chests. I found two; $65 and $75.
But how about that top chest? It looks like a machinist chest for sure. What do you think?
--Bill
- Thu Jan 05, 2023 4:36 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Re: Help Identify Tool Chests
All--
Here's a blownup crop of the label on two of them . . .
--Bill
Here's a blownup crop of the label on two of them . . .
--Bill
- Thu Jan 05, 2023 4:31 pm
- Forum: General Discussion
- Topic: Help Identify Tool Chests
- Replies: 11
- Views: 2113
Help Identify Tool Chests
All--
Can you identify these chests?
Thanks!
--Bill
Can you identify these chests?
Thanks!
--Bill
- Wed Nov 30, 2022 5:18 pm
- Forum: General Discussion
- Topic: Basic reaming mistake
- Replies: 7
- Views: 1941
Re: Basic reaming mistake
Conrad and Harold--
Mistake #2: I had a choke hold on that reamer. All of the shank was stuck up in the collet. Thank you for the guidance.
When I reamed holes for the earlier engines, I probably gripped the shank more like it should be held.
--Bill
Mistake #2: I had a choke hold on that reamer. All of the shank was stuck up in the collet. Thank you for the guidance.
When I reamed holes for the earlier engines, I probably gripped the shank more like it should be held.
--Bill
- Tue Nov 29, 2022 10:31 am
- Forum: General Discussion
- Topic: Basic reaming mistake
- Replies: 7
- Views: 1941
Re: Basic reaming mistake
jcfx--
I used this 1/8" R8 collet.
--Bill
I used this 1/8" R8 collet.
--Bill
- Sun Nov 27, 2022 10:26 pm
- Forum: General Discussion
- Topic: Made some quick change tool holders
- Replies: 25
- Views: 4755
Re: Made some quick change tool holders
Glenn--
Regarding single phase and spool down . . . I could see cranking it up, then shutting it off almost as soon as the tap engaged.
Like liveaboard said, some experience and broken taps would teach you a lot.
--Bill
Regarding single phase and spool down . . . I could see cranking it up, then shutting it off almost as soon as the tap engaged.
Like liveaboard said, some experience and broken taps would teach you a lot.
--Bill
- Sun Nov 27, 2022 9:59 pm
- Forum: General Discussion
- Topic: Made some quick change tool holders
- Replies: 25
- Views: 4755
Re: Made some quick change tool holders
Bill and liveaboard--
Do you slow the spindle down as much as possible?
--Bill
Do you slow the spindle down as much as possible?
--Bill