Setting up a "Precise Super 65" spindle grinder
Setting up a "Precise Super 65" spindle grinder
My lathe chuck being at 0.006" run out started me down the path of putting together an I.D. grinding set up . I have an O.D. grinder already and decided that I wanted a dedicated I.D. unit . I picked up the Super 65 at a decent price , replaced the power cord , brushes and air filter looked good .
I soon relized that 45,000 rpms is way over what the i.d. stones would handle ( learned by research , didn't actually gernade one ) . More down the path , I found a correct speed control unit for the 65 . That is a rather salty price tag . Now I also see many of the photos show a type of chuck for 1/8" or 1/4" mounted stone or cutter bits . Can someone inlighten me on these spindle grinders . I'm wondering if I bought an apple when I should have gotten an orange ... I doing the math , I'm finding I can buy a new chuck for price I'm going to have in the tooling to atempt restoring by old chuck .
Steve S
I soon relized that 45,000 rpms is way over what the i.d. stones would handle ( learned by research , didn't actually gernade one ) . More down the path , I found a correct speed control unit for the 65 . That is a rather salty price tag . Now I also see many of the photos show a type of chuck for 1/8" or 1/4" mounted stone or cutter bits . Can someone inlighten me on these spindle grinders . I'm wondering if I bought an apple when I should have gotten an orange ... I doing the math , I'm finding I can buy a new chuck for price I'm going to have in the tooling to atempt restoring by old chuck .
Steve S
-
- Posts: 1852
- Joined: Tue Dec 06, 2016 4:05 pm
- Location: Elmwood, Wisconsin
Re: Setting up a "Precise Super 65" spindle grinder
"AC-DC" on the nameplate indicates that it is a series motor. A speed control should be quite straightforward. Does it have a tach?
Re: Setting up a "Precise Super 65" spindle grinder
No tachometer , will have to add that to the required component . The speed control is specific to the Super 65 .
Steve
Steve
Re: Setting up a "Precise Super 65" spindle grinder
I doubt the "speed control" is that "specific", I suspect it is no more than a variable transformer, but that's water under the "spent money bridge" now.Steve S wrote: The speed control is specific to the Super 65 .
Steve
I'm also surprised that a smaller dia. stone would require a slower speed than a larger dia. "external" grinding stone.
I'll be following this subject with interest.
Steve
-
- Posts: 1852
- Joined: Tue Dec 06, 2016 4:05 pm
- Location: Elmwood, Wisconsin
Re: Setting up a "Precise Super 65" spindle grinder
That's just a variac. A triac speed control would work as well. You've got yourself a nice variac, though.
Re: Setting up a "Precise Super 65" spindle grinder
That makes no sense. How a wheel (not stone) is applied makes no difference. Rule of thumb for vitrified bonded grinding wheels, regardless of diameter, is to operate at about 6,000 sfpm. Running faster offers the opportunity for the wheel to explode, and yields performance as if the wheel is harder than its rating. Operating slower than recommended speed results in a wheel that behaves as if it is softer than its rating, and won't perform to satisfaction.stevec wrote:I'm also surprised that a smaller dia. stone would require a slower speed than a larger dia. "external" grinding stone.
I'll be following this subject with interest.
Without speed control, the largest wheel that could be safely used with this tool is slightly larger than ½" (9/16" breaks the rule).
Harold
Wise people talk because they have something to say. Fools talk because they have to say something.
Re: Setting up a "Precise Super 65" spindle grinder
Harold ,
sfpm : surface feet per minute ?
sfpm : surface feet per minute ?
Re: Setting up a "Precise Super 65" spindle grinder
yes
Glenn
Operating machines is perfectly safe......until you forget how dangerous it really is!
Operating machines is perfectly safe......until you forget how dangerous it really is!
Re: Setting up a "Precise Super 65" spindle grinder
I wanted to "Thank" everyone so far for their input .
Brings us up to collets . Is there a source for a 1/4" collet head ?
The spindle's output :
It's a 1/4" - 28 tpi shaft , 3/8" long . RH threads .
Which goes to a 1/2" dia. 1/4" long shoulder .
Ends with the 3/4" dia shaft housing .
Steve
Brings us up to collets . Is there a source for a 1/4" collet head ?
The spindle's output :
It's a 1/4" - 28 tpi shaft , 3/8" long . RH threads .
Which goes to a 1/2" dia. 1/4" long shoulder .
Ends with the 3/4" dia shaft housing .
Steve
-
- Posts: 2366
- Joined: Tue Jan 20, 2009 9:33 pm
- Location: Phoenix ,AZ
Re: Setting up a "Precise Super 65" spindle grinder
Non -contact have both ,the non- contact is much better.
www.chaski.com