Basement shop: jim rozen
Moderator: Harold_V
Basement shop: jim rozen
I had promised to put a link to these, so here goes - some of these
are a bit out of date but pretty much accurate.
A view of my basement in peekskill, down the external staircase which
is about five steps. There's a 10L southbend in the background and
a hardinge ESM59 in the foreground:
A very ugly hardinge UM which up until yesterday was the only milling
machine I had in the shop, and a walker turner drill press which has
since been retrofitted with a VFD for variable speed:
A photo showing the three machines together, the echophone
commercial radio in the background is now a hallicrafters SX-26
super defiant however:
Oops, not my shop. Me and my mates at work, me on the right,
and my late boss on the left, just to give some idea of what goes on
there:
Another lathe I've really been enjoying lately, an old pratt and
whitney 7" bench lathe. After the success with the drill press VFD,
I put one on this machine as well:
Mostly I use the machine tools to make parts for, err, other machine
tools. But sometimes motorcycle parts as well:
Somehow the guy in the photo above had his hair bleached out, so
don't pay any attention to that odd effect.
Anyway that's what goes on at 520 highland ave, the latest project
is a venerable pratt and whitney horizontal milling machine just
purchased from steve. Photos of that as the work occurs!
Jim
are a bit out of date but pretty much accurate.
A view of my basement in peekskill, down the external staircase which
is about five steps. There's a 10L southbend in the background and
a hardinge ESM59 in the foreground:
A very ugly hardinge UM which up until yesterday was the only milling
machine I had in the shop, and a walker turner drill press which has
since been retrofitted with a VFD for variable speed:
A photo showing the three machines together, the echophone
commercial radio in the background is now a hallicrafters SX-26
super defiant however:
Oops, not my shop. Me and my mates at work, me on the right,
and my late boss on the left, just to give some idea of what goes on
there:
Another lathe I've really been enjoying lately, an old pratt and
whitney 7" bench lathe. After the success with the drill press VFD,
I put one on this machine as well:
Mostly I use the machine tools to make parts for, err, other machine
tools. But sometimes motorcycle parts as well:
Somehow the guy in the photo above had his hair bleached out, so
don't pay any attention to that odd effect.
Anyway that's what goes on at 520 highland ave, the latest project
is a venerable pratt and whitney horizontal milling machine just
purchased from steve. Photos of that as the work occurs!
Jim
Last edited by jim rozen on Mon Feb 08, 2010 9:42 am, edited 1 time in total.
Nice equipment and photos, Jim. I recognize the work photo as a shielded room as we had them where I worked in the calibration labs at White Sands and Anniston Army Depot. I also have a background as a motorcycle mechanic in the 1950's. Still have some old electronic testing equipment and a few old junk cycles. Recently sold a BMW R60-5.
Don Young
Don Young
-
- Posts: 3803
- Joined: Wed Feb 21, 2007 9:21 pm
- Location: Vallejo California
Jim, you not only have excellent machinery, but that looks to me like a dream shop.
VERY NICE!
I like those copper air lines and that telephone !!
Does it still work?
Thanks for sharing !
VERY NICE!
I like those copper air lines and that telephone !!
Does it still work?
Thanks for sharing !
There are no problems, only solutions.
--------------
Retired journeyman machinist and 3D CAD mechanical designer - hobbyist - grandpa
--------------
Retired journeyman machinist and 3D CAD mechanical designer - hobbyist - grandpa
Thanks -yes, the phone is a western electric space saver. Very handy
right there. But honestly it's the newest phone in that house.
The shop is pretty good right now, but it's hot in the summer, and
humid. In one photo you can see a wash-up sink in the background,
I run a de-humidifier all summer long and gallons of water go down
that sink.
The shop is cold in the wintertime, no heat to speak of since I insulated
the hot water heat loops down there. So I often wear a hat and coat
while working, in the cold months.
We did get about 6 inches of water in there, during hurricane Floyd a
few years ago. I have portable pump standing by for occasions like that!
The overhead in the shop is pretty low, the walker turner drill press has
its head pretty much stuffed up in between the floor joists above. A
birdgeport would never fit down there!
Jim
right there. But honestly it's the newest phone in that house.
The shop is pretty good right now, but it's hot in the summer, and
humid. In one photo you can see a wash-up sink in the background,
I run a de-humidifier all summer long and gallons of water go down
that sink.
The shop is cold in the wintertime, no heat to speak of since I insulated
the hot water heat loops down there. So I often wear a hat and coat
while working, in the cold months.
We did get about 6 inches of water in there, during hurricane Floyd a
few years ago. I have portable pump standing by for occasions like that!
The overhead in the shop is pretty low, the walker turner drill press has
its head pretty much stuffed up in between the floor joists above. A
birdgeport would never fit down there!
Jim
-
- Posts: 3803
- Joined: Wed Feb 21, 2007 9:21 pm
- Location: Vallejo California
I have a kerosene bullet type heater in my garage.
No vent, except the four vents just above the floor, two on each side.
I run it only for a few minutes because it heats up the garage ten degrees in about six minutes.
I am burning diesel in it, at $15.00+ the gallon of kerosene I could afford to run it with that fuel.
No vent, except the four vents just above the floor, two on each side.
I run it only for a few minutes because it heats up the garage ten degrees in about six minutes.
I am burning diesel in it, at $15.00+ the gallon of kerosene I could afford to run it with that fuel.
There are no problems, only solutions.
--------------
Retired journeyman machinist and 3D CAD mechanical designer - hobbyist - grandpa
--------------
Retired journeyman machinist and 3D CAD mechanical designer - hobbyist - grandpa
-
- Site Admin
- Posts: 1730
- Joined: Wed Dec 18, 2002 8:17 pm
- Location: Mesa, AZ USA
Nice shop Jim, been working to finish my basement for months now, and finally am almost up to the shop, doing some wiring. Other than the lathe and Burke mill, which need to be 220V, the table saw, bandsaw, and router are regular 110V tools. I am installing a separate 15A circuit for those and lighting (14/2 wire size). Since I use one machine at a time, I am hoping that will be sufficient.
Best, Nelson
Best, Nelson
A lot of planning and rigging to get it down ok. I have some photos on my group of the lathe move if anyone is interested.matthew_g wrote:Really nice shop you have got there..
I have just one question, Being from Australia and not having basements, How do you manage to get machinery down the stairs and through a standard doorway without droping the machine down or breaking something?
Matt
Nelson